home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-20 / gen21.zip / GEN5.DAT < prev    next >
Text File  |  1991-11-22  |  12KB  |  290 lines

  1. 128D-5.1   B 4-13  PEP  =  [(0.707 PEV)(0.707 PEV)] / RL
  2. How can the output PEP of a transmitter be determined with an
  3. oscilloscope?
  4. A. Measure peak load voltage across a resistive load with an
  5.    oscilloscope, and calculate, using PEP = [(Vp)(Vp)] / (RL)
  6. B. Measure peak load voltage across a resistive load with an
  7.    oscilloscope, and calculate, using
  8.    PEP  =  [(0.707 PEV)(0.707 PEV)] / RL
  9. C. Measure peak load voltage across a resistive load with an
  10.    oscilloscope, and calculate, using PEP  = (Vp)(Vp)(RL)
  11. D. Measure peak load voltage across a resistive load with an
  12.    oscilloscope, and calculate, using
  13.    PEP = [(1.414 PEV)(1.414 PEV)] / RL
  14. *
  15. 129D-5.5   A 4-13  PEV = .5*Vpp,       PEV = 100|Vrms = .707*PEV,  Vrms = 70.7|P = Vrms*Vrms/R,  P = 5000/50
  16. What is the output PEP from a transmitter when an oscilloscope
  17. shows 200-volts peak-to-peak across a 50 ohm resistor connected
  18. to the transmitter output terminals?
  19. A. 100 watts
  20. B. 200 watts
  21. C. 400 watts
  22. D. 1000 watts
  23. *
  24. 130D-5.6   B 4-13  PEV = .5*Vpp,        PEV = 250|Vrms = .707*PEV,  Vrms = 176.8|P = Vrms*Vrms/R,  P = 31240/50
  25. What is the output PEP from a transmitter when an oscilloscope
  26. shows 500-volts peak-to-peak across a 50 ohm resistor connected
  27. to the transmitter output terminals?
  28. A. 500 watts
  29. B. 625 watts
  30. C. 1250 watts
  31. D. 2500 watts
  32. *
  33. 131D-5.7   B 4-13  For a CW signal(unmodulated)|PEP and Average are the same|power level
  34. What is the output PEP of an unmodulated carrier transmitter
  35. when an average-reading wattmeter connected to the transmitter
  36. output terminals indicates 1060 watts?
  37. A. 530 watts
  38. B. 1060 watts
  39. C. 1500 watts
  40. D. 2120 watts
  41. *
  42. 132D-6.1   D 4-7   Oscilloscope
  43. What item of test equipment contains horizontal and vertical
  44. channel amplifiers?
  45. A. The ohmmeter
  46. B. The signal generator
  47. C. The ammeter
  48. D. The oscilloscope
  49. *
  50. 133D-6.2   A 4-7   Signals within the bandwith|capability of the equipment
  51. What types of signals can an oscilloscope measure?
  52. A. Any time-dependent signal within the bandwidth
  53.    capability of the instrument
  54. B. Blinker-light signals from ocean-going vessels
  55. C. International nautical flag signals
  56. D. Signals created by aeronautical flares
  57. *
  58. 134D-6.3   D 4-6   A piece of equipment that|displays signal waveforms
  59. What is an oscilloscope?
  60. A. An instrument that displays the radiation resistance of
  61.    an antenna
  62. B. An instrument that displays the SWR on a feed line
  63. C. An instrument that displays the resistance in a circuit
  64. D. An instrument that displays signal waveforms
  65. *
  66. 135D-6.4   B 4-8   Too much brightness
  67. What can cause phosphor damage to an oscilloscope cathode
  68. ray tube?
  69. A. Directly connecting deflection electrodes to the cathode
  70.    ray tube
  71. B. Too high an intensity setting
  72. C. Overdriving the vertical amplifier
  73. D. Improperly adjusted focus
  74. *
  75. 136D-9.1   C 4-8   A piece of test equipment that|detects signals in a circuit
  76. What is a signal tracer?
  77. A. A direction-finding antenna
  78. B. An aid for following schematic diagrams
  79. C. A device for detecting signals in a circuit
  80. D. A device for drawing signal waveforms
  81. *
  82. 137D-9.2   A 4-8   A signal tracer is used to detect|the presence of a signal
  83. How is a signal tracer used?
  84. A. To detect the presence of a signal in the various stages
  85.    of a receiver
  86. B. To locate a source of interference
  87. C. To trace the path of a radio signal through the ionosphere
  88. D. To draw a waveform on paper
  89. *
  90. 138D-9.3   D 4-8   A signal tracer is used to identify|an inoperative stage
  91. What is a signal tracer normally used for?
  92. A. To identify the source of radio transmissions
  93. B. To make exact replicas of signals
  94. C. To give a visual indication of standing waves on open-
  95.    wire feed lines
  96. D. To identify an inoperative stage in a radio receiver
  97. *
  98. 139D-10.1  B 4-17  Bypass capacitors
  99. What is the most effective way to reduce or eliminate audio
  100. frequency interference to home entertainment systems?
  101. A. Install bypass inductors
  102. B. Install bypass capacitors
  103. C. Install metal oxide varistors
  104. D. Install bypass resistors
  105. *
  106. 140D-10.2  B 4-18  Contact the telephone company|about installing RFI filters 
  107. What should be done when a properly operating amateur station
  108. is the source of interference to a nearby telephone?
  109. A. Make internal adjustments to the telephone equipment
  110. B. Contact a phone service representative about installing RFI
  111.    filters                                                    
  112. C. Nothing can be done to cure the interference
  113. D. Ground and shield the local telephone distribution amplifier
  114. *
  115. 141D-10.3  C 4-17  Radio interference to a PA system for|CW would be on-and-off clicking, SSB-|distorted speech, & AM-audible speech
  116. What sound is heard from a public address system when audio
  117. rectification occurs in response to a nearby single-sideband
  118. phone transmission?
  119. A. A steady hum that persists while the transmitter's carrier
  120.    is on the air
  121. B. On-and-off humming or clicking   
  122. C. Distorted speech from the transmitter's signals
  123. D. Clearly audible speech from the transmitter's signals
  124. *
  125. 142D-10.4  C 4-18  Proper grounding of all equipment
  126. How can the possibility of audio rectification occurring be
  127. minimized?
  128. A. By using a solid state transmitter
  129. B. By using CW emission only
  130. C. By ensuring all station equipment is properly grounded
  131. D. By using AM emission only
  132. *
  133. 143D-10.5  A 4-17  Radio interference to a PA system for|CW would be on-and-off clicking, SSB-|distorted speech, & AM-audible speech
  134. What sound is heard from a public address system when audio
  135. rectification occurs in response to a nearby double-sideband
  136. phone transmission?
  137. A. Audible, possibly distorted speech from the transmitter
  138.    signals
  139. B. On-and-off humming or clicking
  140. C. Muffled, distorted speech from the transmitter's signals
  141. D. Extremely loud, severely distorted speech from the
  142.    transmitter's signals
  143. *
  144. 144D-12.2  D 4-15  A properly adjusted speech processor|improves intelligibility during poor|conditions
  145. What is the reason for using a speech processor with a single-
  146. sideband phone transmitter?
  147. A. A properly adjusted speech processor reduces average
  148.    transmitter power requirements
  149. B. A properly adjusted speech processor reduces unwanted
  150.    noise pickup from the microphone
  151. C. A properly adjusted speech processor improves voice
  152.    frequency fidelity
  153. D. A properly adjusted speech processor improves signal
  154.    intelligibility at the receiver
  155. *
  156. 145D-12.3  B 4-16  Max is Max
  157. When a transmitter is 100% modulated, will a speech processor
  158. increase the output PEP?
  159. A. Yes
  160. B. No
  161. C. It will decrease the transmitter's peak power output
  162. D. It will decrease the transmitter's average power
  163.    output
  164. *
  165. 146D-12.4  C 4-15  A speech processor degrades the signal|quality, thus should not be used when |the frequency in use is clear
  166. Under which band conditions should a speech processor 
  167. not be used?
  168. A. When there is high atmospheric noise on the band
  169. B. When the band is crowded
  170. C. When the frequency in use is clear
  171. D. When the sunspot count is relatively high
  172. *
  173. 147D-12.5  D 4-15  Improves intelligibility during poor|conditions but slightly degrades the|signal quality
  174. What effect can result from using a speech processor with
  175. a single-sideband phone transmitter?
  176. A. A properly adjusted speech processor reduces average
  177.    transmitter power requirements
  178. B. A properly adjusted speech processor reduces unwanted
  179.    noise pickup from the microphone
  180. C. A properly adjusted speech processor improves voice
  181.    frequency fidelity
  182. D. A properly adjusted speech processor improves signal
  183.    intelligibility at the receiver
  184. *
  185. 148D-13.1  A 4-14  This device might generate some |harmonics, so it is best between|the transmitter and low-pass filter
  186. At what point in a coaxial line should an electronic T-R
  187. switch be installed?
  188. A. Between the transmitter and low-pass filter
  189. B. Between the low-pass filter and antenna
  190. C. At the antenna feed point
  191. D. Right after the low-pass filter
  192. *
  193. 149D-13.2  C 4-15  Faster and less likely to wear out
  194. Why is an electronic T-R switch preferable to a mechanical
  195. one?
  196. A. Greater receiver sensitivity
  197. B. Circuit simplicity
  198. C. Higher operating speed
  199. D. Cleaner output signals
  200. *
  201. 150D-13.3  D 4-15  An electronic TR switch is faster|than a mechanical one
  202. What station accessory facilitates QSK operation?
  203. A. Oscilloscope
  204. B. Audio CW filter
  205. C. Antenna relay
  206. D. Electronic TR switch
  207. *
  208. 151D-14.6  B 4-16  An antenna noise bridge is used for  |measuring the impedance of an antenna|or other electrical circuit
  209. What is an antenna noise bridge?
  210. A. An instrument for measuring the noise figure of
  211.    an antenna or other electrical circuit
  212. B. An instrument for measuring the impedance of an
  213.    antenna or other electrical circuit
  214. C. An instrument for measuring solar flux
  215. D. An instrument for tuning out noise in a receiver
  216. *
  217. 152D-14.7  C 4-16  An antenna noise bridge is tuned for|minimum noise in a receiver at the  |desired operating frequency
  218. How is an antenna noise bridge used?
  219. A. It is connected at the antenna feed point, and the
  220.    noise is read directly
  221. B. It is connected between a transmitter and an antenna
  222.    and tuned for minimum SWR
  223. C. It is connected between a receiver and an unknown
  224.    impedance and tuned for minimum noise
  225. D. It is connected between an antenna and a Transmatch
  226.    and adjusted for minimum SWR
  227. *
  228. 153D-15.1  B 4-10  The top half of the display will look |like the input waveform and the bottom|looks like a mirror image of the top  
  229. How does the emitted waveform from a properly adjusted single-
  230. sideband phone transmitter appear on a monitoring oscilloscope?
  231. A. A vertical line
  232. B. A waveform that mirrors the input waveform
  233. C. A square wave
  234. D. Two loops at right angles
  235. *
  236. 154D-15.2  A 4-9   Oscilloscope
  237. What is the best instrument for checking the transmitted signal
  238. quality from a CW or single-sideband phone transmitter?
  239. A. A monitor oscilloscope
  240. B. A field strength meter
  241. C. A sidetone monitor
  242. D. A diode probe and an audio amplifier
  243. *
  244. 155D-15.3  B 4-8   A monitoring oscilloscope displays the|waveform of the transmitted signal
  245. What is a monitoring oscilloscope?
  246. A. A device used by the FCC to detect out-of-band signals
  247. B. A device used to observe the waveform of a transmitted
  248.    signal
  249. C. A device used to display SSTV signals
  250. D. A device used to display signals in a receiver IF stage
  251. *
  252. 156D-15.4  D 4-8   Through a coupling device, connect the|transmitter output to the vertical-   |deflection plates
  253. How is a monitoring oscilloscope connected in a station in order to
  254. check the quality of the transmitted signal?
  255. A. Connect the receiver IF output to the vertical-deflection plates
  256.    of the oscilloscope
  257. B. Connect the transmitter audio input to the oscilloscope vertical
  258.    input
  259. C. Connect a receiving antenna directly to the oscilloscope
  260.    vertical input
  261. D. Connect the transmitter output to the vertical-deflection plates
  262.    of the oscilloscope
  263. *
  264. 157D-17.2  A 4-14  A field strength meter
  265. What is the most appropriate instrument to use when determining
  266. antenna horizontal radiation patterns?
  267. A. A field strength meter
  268. B. A grid-dip meter
  269. C. A wave meter
  270. D. A vacuum-tube voltmeter
  271. *
  272. 158D-17.3  C 4-14  An RF meter with an antenna used for|monitoring relative RF output of an |antenna, transmitter, etc.
  273. What is a field-strength meter?
  274. A. A device for determining the standing-wave ratio on
  275.    a transmission line
  276. B. A device for checking modulation on the output of a
  277.    transmitter
  278. C. A device for monitoring relative RF output
  279. D. A device for increasing the average transmitter output
  280. *
  281. 159D-17.4  A 4-14  A field-strength meter is an RF meter|with an antenna used for monitoring|relative RF output during testing  
  282. What is a simple instrument that can be useful for monitoring
  283. relative RF output during antenna and transmitter adjustments?
  284. A. A field-strength meter
  285. B. An antenna noise bridge
  286. C. A multimeter
  287. D. A Transmatch
  288. *
  289. 
  290.